Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateElite Gate Installation in Fort Worth: What to Know First
Elite gate installation in Fort Worth typically runs $1,900 to $6,800 depending on the gate style, opener model, and site work involved. We’re an independent Elite service provider, not a factory-authorized dealer, but that independence works in your favor: we recommend the right part for the actual problem instead of pushing brand-marked boxes. Turnaround is usually one to two weeks for a full installation after your written estimate is approved.
This page is for Fort Worth homeowners with an Elite gate already on the property, or those considering one. If you’re on the fence about repairing versus replacing an older Elite unit, we’ll give you a straight answer based on what we find. Call (682) 841-5749 and we’ll walk you through it.
Key Takeaways
- We install and service Elite openers and gates across Fort Worth, from Benbrook to Saginaw to the neighborhoods around TCU.
- Every estimate comes in writing before work starts. No work happens until you’ve seen the number and said yes.
- Our technicians show up in shoe covers, lay drop cloths inside your home or garage, and photograph the cleanup before they leave.
- All work carries the 365-Day Done Right Promise. If it’s not right, we make it right.
How Elite Products Fail – and How We Fix Them
Elite gate openers are solid pieces of equipment, but Fort Worth’s heat, occasional freeze cycles, and clay-heavy soil create the same few failure patterns on Elite installations year after year. We see these constantly on jobs across the city, and knowing the pattern saves you from paying for the wrong fix.
- Elite SL3000 gate arm drift. The SL3000 series slide gate operator sometimes loses its limit positions after a power flicker or a hard wind storm. The gate stops a foot short, or overtravels and slams into the end stop. When we install an Elite SL3000 in Fort Worth, we set the limit learning sequence twice and add a surge guard if the panel is on an older breaker. The manual tells you it’ll hold memory; in practice, these units need a little help.
- Mounting plate flex on the CSW200 swing series. This is the one we see most near TCU area homes with brick columns. The CSW200’s stock mounting plate is fine on a flat steel post, but on brick or stone columns the plate flexes just enough to knock the gate’s travel arc out of square. We reinforce the plate with a full-length backing plate before bolting the operator on. It adds an hour to the job and prevents a sagging swing gate a year later.
- Control board corrosion from Texas humidity. Elite’s boards are decently sealed, but garages in Fort Worth can get genuinely humid from late May through September. We open up the enclosure on every Elite install and inspect for green corrosion on the board contacts. If the board shows early oxidation, we clean and seal it. That’s a five-minute step that keeps a $300 board from quietly dying in November.
- Undersized wire from gate to house. This one isn’t Elite’s fault, but it kills Elite units more than anything else. Older Fort Worth homes often have 14-gauge or thinner low-voltage wire coming from an old intercom or a previous owner’s DIY gate attempt. Elite openers want clean power and a clean accessory signal. We run fresh, properly-sized direct-burial wire to the opener on new installations. Undersized wire causes false obstructions and flaky remote range, and no board replacement fixes it.
- Photo eye misalignment on Elite pedestrian gates. When a gate is on a slight slope, as many Fort Worth driveways are, the photo eye transmitter and receiver can sit at slightly different heights after the concrete settles. The gate stops mid-cycle, beeps, and reverses. We shim the eyes with stainless guides and keep the beam slightly above ground level so gravel, leaves, or standing water don’t trigger a false stop. Every Elite install we do includes a slope check before we mount the eyes.
Tell me what the gate is doing, and I’ll tell you what it needs. Usually those are two different conversations.
Styles & brands we work with
Our Elite Gate Installation Process
Every Elite job in Fort Worth follows the same sequence. You’ll know what’s happening at every step, and you’ll see the price in writing before we touch the gate.
- 1
You call, a person answers. No voicemail. We ask basic questions: what model Elite opener you have, what the gate is doing, and whether the gate itself is damaged or just the opener. This tells us what to bring on the first visit.
- 2
On-site assessment. A technician shows up, checks the gate weight, the hinge condition, the post integrity, and the electrical feed. If the gate itself is sound, we’ll quote the opener portion. If the hinges or posts are shot, you’ll see that in the estimate too. Nobody replaces an opener on a failing post; we’d be coming back in a year to fix what should’ve been fixed first.
- 3
Parts decision, clearly explained. For Elite openers, OEM boards and limit assemblies are the way to go when the warranty matters to you. For brackets, photo eyes, and wire, we use quality aftermarket parts that meet or exceed spec without the Elite badge markup. You’ll know which is which on the written estimate.
- 4
Installation day. We bring drop cloths and shoe covers if the control panel or wiring is inside the garage. We use quiet tools if kids are asleep. The installation itself covers mounting, wiring, limit setup, remote programming, and a full cycle test.
- 5
Cleanup and photo. We photograph the finished work area before we leave so there’s no question about how we left it. The floors are clean, the hardware is wiped down, and the old parts are in a bag for you to see.
- 6
Walkthrough and guarantee. We walk you through how the opener works, what the remotes do, and what normal behavior looks like. Then the 365-Day Done Right Promise kicks in. If something isn’t right within the year, we come back and make it right.
What Elite Gate Installation Costs in Fort Worth
Fort Worth pricing for Elite gate installation depends on the gate type, the opener series, and how much site work the job needs. Here are the numbers we typically quote on Elite work in the area:
| Job Scenario | Typical Price Range |
|---|---|
| New Elite CSW200 swing opener on existing single gate | $1,900 – $2,800 |
| New Elite SL3000 slide opener on existing sliding gate | $2,200 – $3,400 |
| Full double gate installation with Elite opener, posts, and hardware | $4,500 – $6,800 |
| Elite pedestrian gate with mag lock and keypad | $1,500 – $2,400 |
| Control board replacement on existing Elite opener | $280 – $520 |
What moves the price: the length and weight of the gate, whether the posts need replacing or reinforcing, how far the electrical run is, and whether we’re dealing with brick, steel, or wood construction. You’ll see the exact number in writing before anything starts, and that’s the number you pay. Call (682) 841-5749 for a free estimate.
See the difference
Before
After
Before
After
Before
AfterWhy Fort Worth Homeowners Call Latch and Post Gate Repair Fort Worth for Elite Work
Most gate companies can bolt on an opener. We’re focused on the whole system: the latch, the post, the opener, and the wiring in between. Every gate comes down to two parts. The latch that holds it and the post that carries it. That’s the job we focus on.
We’re part of the Cedarwell family of independently owned and operated gate specialists, and we’ve been doing this work since 2009. On an Elite job in Fort Worth, you get a technician who knows the SL3000 and CSW200 series by their quirks, not just their model numbers. We service the other brands families actually own too: LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. When an Elite part is backordered, we can usually get you running with an equivalent rather than leaving you waiting four weeks.
Every technician is background-checked, uniformed, and works to the C.A.R.E. values: clean up like it’s our own home, ask before we move or touch anything, respect the family’s time and quiet hours, and explain the price before the work. Shoe covers and drop cloths are standard on every visit, not something you have to request. The 365-Day Done Right Promise covers the whole job, no fine print.
FAQs
No, we are an independent Elite service provider. We’re not affiliated with Elite, and we don’t claim factory authorization. What we do claim is real experience across the Elite product line, and we’ll always tell you when an OEM part matters versus when a quality aftermarket part does the same job for less.
A straightforward opener installation on an existing gate usually takes one full day. A complete new gate with posts, electrical, and an Elite opener typically takes two to three days. We’ll give you a specific timeline in your written estimate. Call (682) 841-5749 to schedule an assessment.
Most of the time, yes, as long as the gate itself is structurally sound and moves freely. The hinge condition and post stability matter more than the gate’s age. We’ll check the gate weight, swing arc, and mounting surface before recommending an opener, and we’ll tell you honestly if the gate needs work before the opener does.
Yes. We run conduit and properly sized low-voltage and line-voltage wire from the house or garage to the gate. Fort Worth code matters here, and we know what’s required. The estimate includes the full electrical run, so there’s no separate electrician to coordinate unless you prefer one.
We’ll work with the warranty process as much as the manufacturer allows for independent service providers. That said, Elite’s warranty typically covers the part, not the labor, and some warranties are voided by improper installation. We install to factory specifications so you don’t lose coverage on a technicality. The exact warranty status comes down to your purchase date and model, and we can walk you through it.
Ready to Get Your Elite Gate Installed?
Call (682) 841-5749 and a live person answers, day or night. We’ll schedule a free on-site assessment, send a technician who knows Elite equipment, and hand you a written price before anything gets touched. That’s how every job starts, and it’s how every job ends too, with a gate that opens and closes the way it should.
Written by Cody Beckman, Owner, Latch and Post Gate Repair Fort Worth at Latch and Post Gate Repair Fort Worth, serving Fort Worth and nearby areas.