Gate Installation in Fort Worth - Free Survey, One Written Price

Fast, Reliable Gate Installation Across Fort Worth

Gate installation in Fort Worth is a different job than it is almost anywhere else in Texas. The clay soil under our city expands and contracts so aggressively between wet springs and dry summers that a poorly set gate post will be out of plumb inside two years. Cody Beckman and our crew at Latch and Post Gate Repair Fort Worth understand this because we work in it every week. We size posts, footings, hinges, and operators for what Fort Worth’s ground actually does, not what a national spec sheet assumes. If you’re planning a new driveway gate, pedestrian gate, or full electric gate system, call (682) 841-5749 for a free estimate and a written price before any work begins.

Call (682) 841-5749

Why Latch and Post Gate Repair Fort Worth Is Fort Worth’s Preferred Gate Installation Company

Homeowners in Fort Worth call us because we treat gate installation as structural work, not a bolt-on job. A wide ornamental steel gate on a long Tanglewood driveway behaves differently than a light aluminum pedestrian gate off Hulen Street. We size the hinge posts, the operator, and the power supply for the actual gate you’re installing – and for the clay it’s sitting in. Our technicians are background-checked, uniformed, and factory-trained on Ghost Controls, DoorKing, Elite, and Mighty Mule, among others. They arrive with shoe covers and drop cloths for any part of the job that touches inside your home, and they take a photo of the clean-up before they leave. That’s the Cedarwell Care Promise, and it’s included on every single visit.

Every installation also carries the 365-Day Done Right Promise. If the gate isn’t right a month or a season later, we make it right. No argument and no fine print. Fort Worth families with kids and dogs care about that – a gate that sags six months after installation isn’t really installed. We’d rather set it correctly the first time, then back it up in writing.

Electric Gate Installation in Fort Worth

Electric Gate Installation in Fort Worth means pairing an operator with a gate that can be 16, 18, or 20 feet wide and built from welded steel or heavy ornamental iron. That’s the norm on our west and north side acreages, where ranch-style homes sit back from the road. The operator has to push real mass through summer heat and winter cold, and the controls have to stay dry through North Texas downpours. A typical electric gate installation in Fort Worth runs $2,800 to $6,500 depending on gate width, weight, operator class, and whether we’re adding solar power or tying into existing mains. You’ll see the exact number in writing before we order a single part.

Solar Power for Long Driveways

Many Fort Worth properties, especially around Walsh Ranch and the acreage west of downtown, have gate entrances three hundred feet or more from the nearest electrical panel. Running conduit that distance gets expensive fast. A properly sized solar system, with a panel mounted for full afternoon sun and a battery bank sized for our short winter days, often costs less than the trenching alone. We spec BFT and Mighty Mule solar-compatible operators for these jobs because they handle high torque without burning through batteries.

Heavy-Duty Operators for Wide Steel Gates

A sliding steel gate on a North Texas driveway can weigh over 800 pounds. Put an undersized residential operator on it and the motor fails inside two summers. We calculate the leaf weight, the cycle frequency, and the wind load before recommending an operator. For most wide steel gates in Fort Worth, that’s a BFT or DoorKing class unit, not a light opener meant for a suburban aluminum gate.

Driveway Gate Installation in Fort Worth

Driveway Gate Installation in Fort Worth usually starts with the driveway itself. Long, curved approaches and wider-than-standard openings mean the gate is often custom, not a stock panel from a big-box shelf. Out in the Walsh Ranch acreage west of downtown, our crew replaced a sagging 20-foot ornamental steel swing gate that had dragged a quarter-inch groove into the concrete during the July dry spell. The hinge post had heaved out of true from the clay swell, so we cut the old post footing, set a new 6×6 steel post in a 4-foot concrete footing with rebar, re-hung the gate with adjustable hinge straps, and added a heavy-duty BFT operator with a solar panel because there was no mains power within 300 feet of the gate. A typical driveway gate installation in Fort Worth runs $3,200 to $8,000 complete, including gate, posts, hardware, and operator.

Swing vs. Sliding on Fort Worth Lots

Swing gates make sense when the driveway has a flat approach and the gate has room to open inward or outward. Sliding gates are better where the driveway slopes or where a swing gate would block a sidewalk or parking area. On clay-heavy lots, we often recommend a sliding gate because it hangs from a track rather than pivoting on hinge posts – fewer posts means fewer things for the clay to push out of plumb.

Post Footings Built for Clay

Fort Worth’s North Texas clay soil expands and contracts so dramatically between wet and dry cycles that gate post footings here need to be set deeper than code minimums. Many local installers, including us, now pour 4-foot concrete footings with rebar cages just to keep a wide steel gate from sagging within two years. The extra concrete costs a few hundred dollars and saves you a re-anchor job every summer.

Trusted Brands We Service in Fort Worth

Cody Beckman keeps our Fort Worth trucks stocked with parts for the brands families actually own around here: Ghost Controls, DoorKing, Elite, and Mighty Mule. That means when we diagnose a failed limit switch or a worn gear on a Mighty Mule opener in Benbrook, we usually have the part on hand the same day. We’re factory-trained on all of them, so the repair or installation is done to the manufacturer’s spec, not improvised. If you’re replacing an old opener or building a new gate from scratch, we’ll recommend the brand and model that fits your gate’s weight and your power situation. Gate Installation is all we do – it’s not a side job between remodels.

Common Gate Installation Problems We See in Fort Worth Homes

• Clay heave pushes the hinge post out of plumb. The post leans, the gate leaf drops, and the latch no longer lines up. The fix is a new post set in a 4-foot concrete footing with rebar, not shims and hope.
• Undersized operators on wide steel ranch gates burn out after a year or two of Texas heat cycles. A light residential opener can’t push an 800-pound gate through a 100-degree afternoon. The motor overheats, the capacitor fails, and you’re calling us anyway.
• Solar-powered openers on long driveways with no shade lose charging capacity in winter. Short days and low sun angles leave the battery undercharged, and the gate dies overnight. We size the panel and battery for December, not June.
• Ornamental iron gates rust at the welds and bind at the hinges after Fort Worth’s humidity and occasional ice storms. A gate that opens fine in October can seize up by February. We treat the metal, replace the hinge pins, and set the gaps so the gate swings through a full thermal cycle.

Pricing for Gate Installation in Fort Worth, TX

We Also Serve Cities Near Fort Worth

Our crews regularly install gates in Haltom City, Hurst, Kennedale, and Arlington. The soil and climate issues are similar, but each city has its own lot patterns and driveway approaches. If you’re in one of those communities, we bring the same written pricing, the same footing specs, and the same 365-Day Done Right Promise. Read more about Gate Installation in Fort Worth or call us for your specific street and gate size.

FAQs About Gate Installation in Fort Worth