Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Motor & Opener Cost in Fort Worth?
Gate motor and opener replacement in Fort Worth typically runs between $850 and $2,600 for most residential properties, with the average homeowner paying about $1,450. A basic chain-drive opener on a single swing gate starts around $700, while a heavy-duty sliding gate motor with battery backup and keypad entry can reach $3,500 or more. Those numbers include the motor itself, installation labor, and standard control wiring.
- Basic swing gate opener: $700 – $1,200 installed
- Sliding gate motor: $1,100 – $2,400 installed
- Premium operator with battery backup: $2,200 – $3,500 installed
- Motor replacement only (labor included): $450 – $1,100
- Control board or receiver repair: $180 – $480
At Latch and Post Gate Repair Fort Worth, you’ll see the exact number in writing before we touch anything. That’s the Cedarwell Care Promise, and it’s included on every visit.
Gate Motor & Opener Cost Breakdown (2026)
Here’s the line-item picture for the Fort Worth market as of 2026. These are real ranges drawn from what we see on service calls from Benbrook to North Richland Hills, not national averages that don’t reflect Texas heat, soil movement, or local labor rates.
| Line Item | Typical Range (Fort Worth, 2026) |
|---|---|
| Entry-level swing gate opener (chain or belt drive, single gate) | $350 – $650 (parts); $700 – $1,200 installed |
| Mid-range slide gate motor (1/2 HP, 18 – 22 ft gate) | $600 – $1,100 (parts); $1,100 – $1,900 installed |
| Heavy-duty slide gate operator (1 HP, 30+ ft, commercial-grade) | $1,400 – $2,600 (parts); $2,200 – $3,500 installed |
| Battery backup system | $250 – $600 |
| Keypad entry (wireless or wired) | $120 – $350 |
| Safety sensor kit (photo eyes, edge sensors) | $90 – $280 |
| Control board replacement | $180 – $480 |
| Remote transmitter (per unit) | $40 – $95 |
| Labor (standard installation, 2 – 4 hours) | $200 – $550 |
| Old motor removal and disposal | $50 – $150 |
What moves the needle? Brand choice is the biggest one. A LiftMaster or FAAC operator runs higher than a Mighty Mule, but you’re paying for duty cycle and weather sealing that matter in Tarrant County’s July heat and March wind. Gate weight and length are second. A 16-foot ornamental steel swing gate needs more torque than an 8-foot aluminum one. And third: whether you already have conduit run for low-voltage wire. If we need to trench 40 feet across a driveway to get power to the motor, that adds $15 to $25 per linear foot.
What Affects Gate Motor & Opener Pricing in Fort Worth
- Gate type and weight. Solid steel gates with cedar infill panels are common in Westworth Village and weigh far more than tubular aluminum. A heavier gate requires a higher-torque motor, which costs more up front but wears out less quickly.
- Brand and availability. We’re factory-trained on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Replacement parts for FAAC and BFT sometimes have a two-week lead time from the distributor, and that can affect the final quote.
- Power access. Fort Worth lots in neighborhoods like Wedgwood and Ridglea Hills often have detached garages and long driveway runs. If no low-voltage wire is already stubbed near the gate post, trenching adds real money.
- Control features. A basic two-button remote is cheap. Adding smartphone app control, a keypad, intercom, or integration with a driveway alarm increases both parts and programming time.
- Age of the existing gate hardware. If the gate hinges, post brackets, or wheels were installed in the 1990s with the original gate, they may need reinforcement before a new motor is mounted. We’ll tell you if that’s the case and show you the number before starting.
- Texas weather exposure. Full sun and no shade canopy means plastic gear components in cheap operators fail faster here than in milder climates. We recommend sealed gearboxes and metal housings for any gate with western exposure in Fort Worth.
How to Save on Gate Motor & Opener
Saving money on a gate opener doesn’t mean buying the cheapest motor online. It means choosing the right motor for your gate’s actual weight and duty cycle, and getting the installation done once.
Here’s what we tell homeowners to look at:
- Match the motor to the gate, not the marketing. You don’t need a 1 HP commercial operator for an 8-foot aluminum walk gate. You need maybe 1/3 HP. Overspending on capacity you’ll never use is the most common waste we see.
- Bundle the accessories during installation. Adding a keypad or battery backup while the technician is already on site is cheaper than a second service call later. The labor is already there.
- Ask about a motor-only replacement if the gate and wiring are still sound. If your existing operator failed but the gate itself, hinges, and conduit are in good shape, a motor-only swap can save $500 or more versus a full operator and arm kit.
- Check your homeowner’s insurance for weather-related damage. Fort Worth hail and wind storms occasionally damage gate operators. Some policies cover replacement after a named storm event.
- Get the written price before the work starts. Every Latch and Post visit includes a written estimate before any work begins. That means you can compare numbers without pressure. Call (682) 841-5749 for a free estimate, and we’ll walk the gate with you.
How a Gate Motor & Opener Installation Works
If you’ve never replaced a gate operator before, here’s the sequence we follow on a typical Fort Worth job. Understanding this helps you see where the labor hours go.
- On-site assessment. We measure the gate width, weigh the gate by lifting it off its hinges or by checking the existing motor’s rating, and inspect the post, brackets, and power source. We write down the findings.
- Written price. You get a line-item quote before any work starts. No deposit required, no pressure to accept on the spot. This is the Cedarwell standard on every visit.
- Prep and protection. We lay drop cloths in the entry path, put on shoe covers before stepping inside your home, and keep the work area contained. Pets stay safe, floors stay clean.
- Old operator removal. We disconnect power, remove the old motor and arm, and haul it away. We also check the gate’s swing path and hinge condition while the gate is free to move.
- New motor mounting. The operator is mounted to the gate post or pad, aligned with the gate’s travel, and torqued to spec. For slide gates, we check the track and rollers before mounting the motor.
- Wiring and controls. Low-voltage wiring, safety sensors, keypad, and remotes are connected. We program limits, force settings, and any smart controls you chose.
- Testing and cleanup. We run the gate through 10 to 15 full cycles, test the safety reverse, and adjust speed. Then we clean up, take a photo of the finished work area, and walk you through the new system before leaving.
Gate Motor & Opener Brands We Service and Install in Fort Worth
One of the reasons our pricing is consistent across Fort Worth is that we only work on brands we’ve been factory-trained to service. If you call us about a brand we don’t touch, we’ll tell you honestly and point you to someone who does. That’s the whole point of being a gate specialist.
We service and install:
- LiftMaster – the most common brand in Fort Worth HOAs. Parts are locally available, and programming is straightforward.
- FAAC – Italian-built, hydraulic operators. Smooth and quiet, but require brand-specific parts that occasionally have longer lead times.
- BFT – another Italian manufacturer, common in gated communities in the Alliance corridor. Excellent duty cycles for high-use gates.
- Linear – common on older Fort Worth properties. We still service them, but replacement parts are becoming harder to find, which may push you toward a full unit swap.
- Viking – heavy-duty slide gate operators. A favorite for ranches and acreage properties southwest of the city near Aledo.
- Ghost Controls – popular for DIY-installed solar gate openers. If the previous owner installed one and it’s acting up, we can often repair or reinstall it properly.
- DoorKing – very common in commercial and multi-tenant settings, but we see their residential models around TCU and Paschal neighborhoods.
- Elite – gate operators you’ll find on custom homes in Mira Vista and Montserrat.
- Mighty Mule – budget-friendly, widely available. Good for light gates but we caution against using them for anything over 16 feet or 550 pounds.
For a deeper look at what we do with these systems, see our Gate Motor & Opener in Fort Worth page.
Real Fort Worth Gate Motor Scenarios and What They Cost
These are the kinds of calls we get every week. The numbers are what we actually quoted in the last 12 months across Fort Worth, not averages from a national database.
Scenario 1: “Our swing gate stopped opening. The motor hums but nothing moves.”
We found stripped plastic gears inside a 9-year-old Mighty Mule operator on a 12-foot aluminum gate in the Ryan Place neighborhood. The arm motor was done. We replaced the operator with a mid-range LiftMaster swing arm, reused the existing keypad wiring, and added new safety photo eyes because the originals were sunbaked and cloudy. Total: $1,380.
Scenario 2: “We just bought a house in Benbrook and the sliding gate opener is from 2004.”
The gate was a 20-foot iron slider with a vintage Linear operator. The motor still worked but the control board was failing intermittently. We quoted a board replacement at $340, but told the homeowner up front that the motor itself was near the end of its expected life. They chose a full replacement with a 1/2 HP Viking operator and a new battery backup. Total: $2,450.
Scenario 3: “The gate opens but won’t stop at the right place. It slams.”
On a home near Eagle Mountain Lake, limit switches on a FAAC 750 operator had gone out of adjustment. It took 45 minutes to reset and recalibrate. We also replaced the gate’s worn stop pad while we were there. Total: $275.
Scenario 4: “Can we get a gate opener for a double swing gate on a buckled concrete pad?”
We see this a lot in Fort Worth, where clay soil expands and contracts under driveway pads. The two gate posts were out of alignment by 3/4 inch. We installed a heavy-duty LiftMaster dual-swing opener with an adjustable arm kit that compensated for the misalignment, and recommended a post remount within the next two years. Opener and install: $2,150. We flagged the post issue separately with a written estimate, no pressure.
FAQs – Gate Motor & Opener Cost
How much does it cost to replace a gate motor in Fort Worth?
Most gate motor replacements in Fort Worth run between $450 and $1,100 when the existing gate, hinges, and wiring are in good condition and only the operator itself needs swapping. The average call we do lands around $800. Call (682) 841-5749 and we’ll give you a written quote before any work starts.
Is it cheaper to repair a gate opener or replace it?
Repairs under $300 are usually the better call on a motor that’s less than 8 years old. Once the repair estimate passes roughly 50% of the cost of a new operator, replacement makes more sense. We’ll tell you straight and show you both numbers before we touch anything.
How long does a gate motor installation take?
A standard single-gate operator replacement takes 2 to 4 hours on site. A full sliding gate motor with new wiring, keypad, and battery backup can take 5 to 7 hours. If trenching is needed for power, plan for a follow-up visit after the conduit is run.
What gate opener brand is most reliable in Texas heat?
We see the fewest heat-related failures in LiftMaster, FAAC, and Viking operators. The key is a sealed metal gearbox and a control board rated for high ambient temperatures. Cheap plastic-gear openers fail faster in Fort Worth summers, especially with full western sun exposure.
Can you install a gate opener on an existing gate without replacing the gate?
Yes, in most cases. The gate needs to swing or slide freely and have a sound post or pad to mount the operator. We’ll assess that during the free estimate and include any needed bracket upgrades in the written price. Estimates are free at (682) 841-5749.
Why Pricing Stays Straightforward With Latch and Post
Every gate comes down to two parts: the latch that holds it and the post that carries it. That’s the job we focus on, and it’s why our pricing doesn’t wander. We’re not a general handyman service that happens to do gates. We’re the Latch and Post Gate Repair Fort Worth team, part of the Cedarwell family of independently owned and operated gate specialists since 2009.
Here’s what you can expect, spelled out:
- A written price before work begins. Every visit, no exceptions. You’ll see parts, labor, and any disposal fees listed separately.
- Shoe covers and drop cloths on every job. If the work requires us to step inside your home, your floors stay the way we found them. We also send a cleanup photo before we leave.
- Background-checked, uniformed technicians. Trained on the brands families actually have in Fort Worth: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
- Quiet tools when kids are asleep. If nap time matters, let us know. We’ll schedule around it.
- A live person answers the phone. 24 hours a day, 7 days a week. Nights, weekends, holidays. No voicemail tree, no callback queue.
- The 365-Day Done Right Promise. If the repair or installation isn’t right, we make it right. No argument, no fine print.
We choose pet-safe lubricants where there’s a choice, and we ask before we move or touch anything on your property. That’s the C.A.R.E. standard: Clean up like it’s our own home, Ask before we move or touch anything, Respect your time and quiet hours, Explain the price before the work.
If your gate won’t open, moves slowly, or the opener sounds like it’s grinding, call us at (682) 841-5749 for a free estimate. Cody Beckman leads our Fort Worth team, and he’ll make sure the number you hear on the phone is the number you see in writing before we touch a single bolt.
Written by Cody Beckman, Owner at Latch and Post Gate Repair Fort Worth, serving Fort Worth since 2009.
Pricing reflects the Fort Worth market as of 2026. Latch and Post Gate Repair Fort Worth offers free estimates – call (682) 841-5749.
What Our Customers Say
"The gate screeched and dragged. They fixed the track and oiled it, and wiped down everything after so there was no mess. Quiet and kind, in and out without any fuss."
- Opal Reddick"Electric gate was acting up. He was calm and methodical, found the bad sensor, and tidied the whole area by the gate post when he finished. No grease left on the driveway."
- Ravi Menon"Electric gate was sticking. He oiled and adjusted the track, wiped everything down after, and left no grease anywhere. Quiet, kind, and quick."
- Carlene Fuchs